a rare block of time became free, so I did what I feel compelled to do every few months whether I need to or not – rebuild the studio. or rather, reconfigure it, find better ways to process and route, alter and effect, record and playback…loop and delay.
each time I go through this process, hopefully, things get a little better. there are fewer long cable runs, devices are more organised, and new signal paths are invented that should, theoretically, at least, give me the most and best sonic options to record with. time will tell!
it used to be that this was just a pedal board rebuild, but the last real pedalboard I built, in 2005, is long since retired, and now I have “floating” pedal boards – the kind without the board. 🙂
so this time, I wanted to ensure that I would have as little as possible to do in the way of “custom connections” when I want to record. the idea being, that every instrument, plus a selection of special paths for guitar, has it’s own pair of stereo tracks on the mixer (or mono in a few cases) – and I mean every instrument.
one part of the configuration that did not change is the final processing prior to the signal paths terminating in the sound card – as I had in the last set up, I take a stereo output of the mixer (which is not being used as a normal mixer, but rather as a guitar and keyboard processing mixer, if you will) and it goes first to the roland rc-50 in stereo, and then the roland goes out in stereo to the digitech time bender delay so I can have beautiful, long fades of either the loop that’s running, and/or any live material at the end of a piece.
this particular set up, with my “best” stereo looper and “best” delay as the last two items in the chain, after the OUTPUT of the mixer, but prior to the sound card, has worked so well, that I think I will probably reiterate it in every new set up – I just can’t think of a better way. my only regret with this routing is that I don’t have a very, very expensive and beautiful hardware reverb to put after the delay. 🙂
while that used to be a priority, it isn’t now, at least not at the moment, because having the full version of breeze allows me to apply amazing reverberant sounds in post-production, which is fine for the moment.
since I’m in hardware dreamland for a moment, please add in an eventide harmoniser too, just before the looper I think. 🙂
so in the current rebuild, knowing I would want to keep the end of the chain the same, I made sure it was set up first – so I completed the configuration of the last part of the signal chain before I even began to think about the instrument and input side !
then, working backwards, I started to try and map out how I wanted the routing to be with a view to make things as simple as possible when improvising live and recording.
starting with the guitars, then, since they are the trickiest.
the core of the guitar system is of course the roland gr-55, and the first part of the signal chain is based on it being the central input device – so the guitar synthesizer itself, is connected via the special cable to the synth – and this is simplicity itself, actually, it then goes out as a stereo pair to the first two channels of the mixer.
that takes care of three of the four component sounds the synth produces: synth voice 1,
synth voice 2, and the modelled guitar tone – all three, in stereo, taken from the main stereo
out of the gr-55 directly to channels 1 and 2 of the mixer.
guitar synth > stereo out > mixer channels 1 & 2
then we come to the fourth component, which has a separate output on the back of the gr-55, which is the unaffected, normal guitar sound. what happens to it…is a little more complex.
in my previous set up, I had this particular component, the unaffected guitar out of the synth, split via an a/b box, one line going to the line 6 X3 live, the other, through the stomp boxes chain. that worked OK, but I wanted more finite control, and more choices – so this time, it’s now the a/b/c box instead – why not? J
so the unaffected guitar out of the gr-55 comes out of the synth and goes into the “common” or “in/out” of the a/b/c box. it can then be switched to either path a, path b or path c. those are now to be configured as follows, each returning to its own mixer pair or channel:
path a: guitar > whammy II pitch pedal > line 6 x3 live > stereo out > mixer channels 3 & 4
path b: guitar > v-wah (modelling wah/distortion) > rc-20xl looper > boss ce-5 stereo chorus > boss bf-3 stereo flanger > boss rv-5 stereo digital reverb > line 6 dl-4 stereo delay > stereo out > mixer channels 5 & 6
path c: guitar > boss md-2 distortion > roland volume pedal > mono out > mixer channel 7
optionally: path c can be routed to a small, miked up practice amp instead of being routed through the mixer.
(note: mixer channel 8 remains unassigned – for future stereo device options)
so, by creating this scenario, any of the three paths a/b/c can be played in conjunction with the currently chosen guitar synth voice, and, of course, using the a/b/c switch, allows me to switch between three pre-configurable guitar sounds.
additionally, this “unaffected voice” on the guitar synth can actually be set up with it’s own internal effects within the gr-55’s programming parameters, so additional sounds can be set up to sit “before” the three paths as well – talk about flexibility.
of course, in reality, most of the time, I will use a blend of stereo guitar synth and stereo x3 live (or sometimes, just one of those), and the stomp box chains are just for the occasional foray into some of the different sounds available via the stomp boxes – all of which have their own unique characters.
each of the three chains was designed carefully so as to be unique as possible – the x3 chain, path a, of course has a massive library of amazing sounds just by itself, while path b allows me to use the combination distortion/wah sounds of the v-wah to drive a classic chain of modulation, reverb and delay devices – total pedal-mania there! and finally, path c is really just for fuzz tone soloing, with the volume pedal mainly present to clamp down on output noise once a solo completes, or to fade in a sinister buzzing solo…
future work is to re-invent using S-PDIF digital input for the X3 which supports that, recording it’s output directly, digitally, to the sound card – and once I get that working again, I might actually not use the mixer inputs any more – since I would have a super clean digital version recorded on the separate s-pdif channels – although I may also investigate routing the x3 live mixer channels to a different pair of inputs on the sound card, instead of having them “all in one basket” – the only disadvantage of that being that I would then “lose” the ability to instantly loop and then delay the sound of the x3 live – but that might be ok.
I also want to think about using amplifiers again, a small, low level amp with a great tone, miking that up and recording it on separate sound card channels, so I can then mix that raw guitar amp “tone” with the sounds captured by the mixer into the sound card. that is for the future though – and I could see a classic pignose amp in there too, perhaps someday, and maybe an envelope follower to go with it, so I can do some proper fz tones…
and that is pretty much it for the guitar “section”, except to say, there are various continuous controller or expression pedals here and there in the set up, which I am developing slowly as I go to control real time parameters with during live performance, I am particularly interested in what I may be able to accomplish with the expression pedal for the digitech time bender delay that currently sits at the very end of the signal chain, but many of the devices support expression pedals, and I want to work more with the amazing sounds that can be achieved by being able to control effect levels of devices as you are playing.
finally we now move to the world of keyboards and x-y pads, which is a much more straightforward affair, except this time, I’ve made all three of my synths and the kaossilator available in the mixer, so that if I so desired, I could turn all three of them on, and play all three at once – live. one in stereo and two in living mono. J
to accomplish this, here’s how the “keyboard” half of the mixer looks now:
m-audio prokeys sono 88 stereo keyboard > stereo out > mixer channels 9 & 10 (ganged channel)
note: of course, this is just the stereo out of the audio of the prokeys – for it’s stock audio voices. at the same time as these can be recorded through the mixer, of course the same keypress that drives the stereo audio out ALSO drives MIDI, which can of course run one or more pianos, synthesizers, or mellotrons within SONAR – so this stereo feed is just one part of what the prokeys can create in terms of sound – and in fact, early trials show that a “blend” of MIDI keyboards and this live audio out can be very effective indeed.
yamaha dx7s keyboard > mono out > mixer channels 11 & 12 (ganged channel)
yamaha dx11s keyboard > mono out > mixer channels 13 & 14 (ganged channel)
korg kaossillator x-y pad synthesizer > stereo out > mixer channels 15 & 16 (ganged channel)
and remarkably, that is it. reconfiguring this took most of the afternoon, but the majority of the work is done, so all that remains is testing (you never know when one or more of your trusty cables will just pack up and stop working), level setting and to see if it all works as expected, make any last minute tweaks – and then go back to work!
of course, the unknown right now is…will it work, and, will it sound good? but, the good news is, if either is a problem – well, that just means a little more effort will be required until it does sound good.
you can’t really go wrong, because the two core devices sound very good already, without a lot of help from me, it usually the stomp boxes that are a little trickier to get “sounding right” – but, I am sure it will all work well enough, and I should be all set for another six months or until I get another “idea” about how I can make the system work more efficiently, or if I add new devices in, and so on…
I will find out what works and what doesn’t, and respond accordingly.
now, I am going to turn back to the assessments of “the dozey lumps” (including electric material, and progressive rock covers, from the same band in electric mode – a band I am calling “proto-bindlestiff” at the moment mentally) rehearsals and concerts that I’ve been converting from cassette few days, and see what sonic gems I can extract from the distant musical past, as well as beginning to transfer some of the very earliest dave stafford recordings – starting with the first known recording of dave stafford playing music – a band concert from 1971 when I was just 13 years old…58 minutes of musical history?? 🙂